DIY Bathtub Installation.
DIY Bathtub Installation.
Blog Article
Listed here in the next paragraph you'll find lots of good quality resources pertaining to Tools You Need to Install a New Bathtub .
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably hard job. If the old bathtub is easily easily accessible, the job can move rapidly; if you need to open a wall to eliminate the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified on your own for the job and are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is much better to consider employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This post will aid you mount a brand-new tub in your restroom if you have already bought a new bathtub and also do not need to change the arrangement of your previous water supply pipelines.
Your devices and also material checklist should comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water system. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome as a result of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker offered backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be connected to the tap finishes initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap port to the proper supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise inspect the overflow outlet and also the regular electrical outlet for leaks.
Finally, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its final position.
Preparing for the Installment
To start with, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to ensure that if the tap features a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to split an inflexible seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about complications with moisture and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also fittings. They are offered in tubes and also cartridges, and can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our post on Installing A Bathtub. Thanks so much for taking time to read through our posting. Enjoyed our write up? Please share it. Let somebody else check it out. Thank you for taking the time to read it.
Customer Reviews Report this page